![]() The vpls-id parameter must be unique for each tunnel between this tunnel and the remote peer and identifies the VPLS tunnel. VPLS tunnel configurations are in the /interface VPLS menu. In fact, this label ensures traffic delivery to the other endpoint of the tunnel. To forward data in the tunnel, you need to impose 2 labels on packets which are the tunnel label and the transport label. The LDP protocol negotiates VPLS tunnels – both endpoints exchange tunnel labels to use for the tunnel. Establish the following tunnels to achieve transparent ethernet segment forwarding between customer sites:Įach tunnel setup involves creating VPLS interfaces on both tunnel endpoints. You can consider the VPLS interface as a tunnel interface like the EoIP interface. In this section, you will learn how to configure VPLS on Mikrotik. We already taught how to Setup MPLS in Mikrotik in previous posts. It provides the best solution to create a wide, interconnected, and secure network. In fact, For customers implementing VPLS, all sites will be on the same Ethernet LAN. This technology enables you to connect geographically dispersed Ethernet local area network (LAN) sites to each other across an MPLS backbone. VPLS stands for Virtual Private LAN Service and is a way to provide an Ethernet-based multipoint to multipoint communication over IP or MPLS networks. ![]() ip/firewall/nat/add action=src-nat chain=srcnat comment="Hairpin to LAN2" out-interface=bridge-lan-01 src-address=172.16.0.0/23 to-addresses=172.16.0.Recommended Article: How to Change Cisco Switch Port to Routed Port What is VPLS? ip/firewall/nat/add action=masquerade chain=srcnat comment="Masquerade WAN (non-ipsec)" ipsec-policy=out,none out-interface-list=WAN routing/rule/add dst-address=172.16.0.0/23 table=main action=lookup comment="to LAN2" routing/rule/add dst-address=192.168.88.0/24 table=main action=lookup comment="to LAN1" tool/mac-server/mac-winbox/set allowed-interface-list=LANĪdd address=0.0.0.0/8 comment="\"This\" Network" list=BOGONSĪdd address=10.0.0.0/8 comment="Private-Use Networks" list=BOGONSĪdd address=100.64.0.0/10 comment="Shared Address Space. tool/mac-server/set allowed-interface-list=LAN ip/neighbor/discovery-settings/set discover-interface-list=!WAN interface/list/member/add interface=bridge-lan-02 list=LAN interface/list/member/add interface=bridge-lan-01 list=LAN ![]() interface/list/member/add interface=pppoe-02 list=WAN comment=PPPoE-02 interface/list/member/add interface=pppoe-01 list=WAN comment=PPPoE-01 interface/list/member/add interface=ether2 list=WAN comment="Uplink WAN for PPPoE-02" interface/list/member/add interface=ether1 list=WAN comment="Uplink WAN for PPPoE-01" interface/list/add name=LAN comment="For Local Area Networks"Īdd disabled=no interface=ether1 name=pppoe-01 add-default-route=no user=fpt1 password=fpt1Īdd disabled=no interface=ether2 name=pppoe-02 add-default-route=no user=vnpt1 password=vnpt1Īdd bridge=bridge-lan-01 interface=ether3Īdd bridge=bridge-lan-01 interface=ether4Īdd bridge=bridge-lan-01 interface=ether5 ![]() Send your feedback to /interface/list/add name=WAN comment="For Internet" In this script I assume you have 2 pppoe WAN links: Please try my RouterOS 7 multiwan PPPoE loadbalance scriptġ) This script allows you to send traffic from special address lists via certain pppoe connection, bypassing the load balance logic (for example your TV should always go only via pppoe-02)ģ) This script solves the multiwan issue when you are building outgoing VPN tunnels (openvpn, wireguard, IPSec etc).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |